This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 and PORT3.1 This ARM Example may be debugged using only the uVision Simulator and your PC--no additional hardware or evaluation boards are required. The Simulator provides cycle-accurate simulation of all on-chip peripherals of the ADuC7000 device series. You may create various input signals like digital pulses, sine waves, sawtooth waves, and square waves using signal functions which you write in C. Signal functions run in the background in the simulator within timing constraints you configure. In this example, several signal functions are defined in the included Startup_SIM.INI file.
资源简介：This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PO...
上传时间： 2013-12-19
上传用户：Yukiseop
资源简介：STR71x Flash IAP Example This project is an RV-MDK adaptation of the ST Application Note: "STR71x In-Application Programming using UART". Please see http://www.st.com/stonline/products/literature/anp/11026.htm for details.
上传时间： 2014-01-11
上传用户：sz_hjbf
资源简介：This project contains code for testin realloc api tested in fre rtos ported to AT91SAM7x256.the code is compiled using IAR embedded work bench for ARM
上传时间： 2013-12-14
上传用户：wkchong
资源简介：The goal of this project is to explore the idea of point-based radiosity, which is a shooting radiosity technique suggested by Mark Harris at UNC. The primary idea is that features available in graphics hardware can be utilized to perfor...
上传时间： 2015-08-24
上传用户：change0329
资源简介：SAM9261 BasicMMU Example code with ADS1.2 (163 kB) The goal of this project is to show how to use a PC100 SDRAM and the MMU to perform a rating with a 100MHz Bus Clock. The rating is based on Dhrystone 2.1. It shows the rate when I+D Caches...
上传时间： 2013-12-28
上传用户：zhanditian
资源简介：The main purpose of this project is to add a new scheduling algorithm to GeekOS and to implement a simple synchronization primitive (semaphore). As you might have already noticed, GeekOS uses a simple priority based preemptive Round Robin a...
上传时间： 2013-11-27
上传用户：Late_Li
资源简介：The purpose of this project is to make it possible to remotely switch on a Webasto Thermo Top C water heater that is used to pre-heat the heating system of a car without starting the motor.
上传时间： 2013-12-28
上传用户：LouieWu
资源简介：The LM35 of National Semiconductors that is used in this project is a precision centigrade temperature sensor, which has an analog output voltage. It has a range of -55潞C to +150潞C and a accuracy of 卤0.5潞C . The output voltage is 10mV/...
上传时间： 2017-04-16
上传用户：D&L37
资源简介：The purpose of this project is to explore the issues and implementation of a multiple instruction stream, single data stream processor. We are running two instruction streams on two CPUs which share an address space. The processors share a ...
上传时间： 2017-04-18
上传用户：731140412
资源简介：This project is to design the automated system for the inventory of Al-Ahmad Cotton and Oil Mills situated at Vehari road, Multan. It is difficult to keep the track of sale purchase and production system of any company, department or organi...
上传时间： 2013-12-22
上传用户：qq1604324866
