#ifndef _AHA152X_H
#define _AHA152X_H
/*
* $Id: aha152x.h,v 0.2 1993/10/03 00:58:03 root Exp $
*/
#include "../block/blk.h"
#include "scsi.h"
#if defined(__KERNEL__)
#include
int aha152x_detect(int);
const char *aha152x_info(void);
int aha152x_command(Scsi_Cmnd *);
int aha152x_queue(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
int aha152x_abort(Scsi_Cmnd *, int);
int aha152x_reset(Scsi_Cmnd *);
int aha152x_biosparam(int, int, int*);
/* number of queueable commands
(unless we support more than 1 cmd_per_lun this should do) */
#define AHA152X_MAXQUEUE 7
/* Initial value of Scsi_Host entry */
#define AHA152X { /* name */ "Adaptec 152x SCSI driver", \
/* detect */ aha152x_detect, \
/* info */ aha152x_info, \
/* command */ aha152x_command, \
/* queuecommand */ aha152x_queue, \
/* abort */ aha152x_abort, \
/* reset */ aha152x_reset, \
/* slave_attach */ /* NULL */ 0, \
/* bios_param */ aha152x_biosparam, \
/* can_queue */ 1, \
/* this_id */ 7, \
/* sg_tablesize */ SG_ALL, \
/* cmd_per_lun */ 1, \
/* present */ 0, \
/* unchecked_isa_dma */ 0 }
#endif
/* port addresses */
#define SCSISEQ (port_base+0x00) /* SCSI sequence control */
#define SXFRCTL0 (port_base+0x01) /* SCSI transfer control 0 */
#define SXFRCTL1 (port_base+0x02) /* SCSI transfer control 1 */
#define SCSISIG (port_base+0x03) /* SCSI signal in/out */
#define SCSIRATE (port_base+0x04) /* SCSI rate control */
#define SELID (port_base+0x05) /* selection/reselection ID */
#define SCSIID SELID /* SCSI ID */
#define SCSIDAT (port_base+0x06) /* SCSI latched data */
#define SCSIBUS (port_base+0x07) /* SCSI data bus */
#define STCNT0 (port_base+0x08) /* SCSI transfer count 0 */
#define STCNT1 (port_base+0x09) /* SCSI transfer count 1 */
#define STCNT2 (port_base+0x0a) /* SCSI transfer count 2 */
#define SSTAT0 (port_base+0x0b) /* SCSI interrupt status 0 */
#define SSTAT1 (port_base+0x0c) /* SCSI interrupt status 1 */
#define SSTAT2 (port_base+0x0d) /* SCSI interrupt status 2 */
#define SCSITEST (port_base+0x0e) /* SCSI test control */
#define SSTAT4 (port_base+0x0f) /* SCSI status 4 */
#define SIMODE0 (port_base+0x10) /* SCSI interrupt mode 0 */
#define SIMODE1 (port_base+0x11) /* SCSI interrupt mode 1 */
#define DMACNTRL0 (port_base+0x12) /* DMA control 0 */
#define DMACNTRL1 (port_base+0x13) /* DMA control 1 */
#define DMASTAT (port_base+0x14) /* DMA status */
#define FIFOSTAT (port_base+0x15) /* FIFO status */
#define DATAPORT (port_base+0x16) /* DATA port */
#define BRSTCNTRL (port_base+0x18) /* burst control */
#define PORTA (port_base+0x1a) /* PORT A */
#define PORTB (port_base+0x1b) /* PORT B */
#define REV (port_base+0x1c) /* revision */
#define STACK (port_base+0x1d) /* stack */
#define TEST (port_base+0x1e) /* test register */
/* bits and bitmasks to ports */
/* SCSI sequence control */
#define TEMODEO 0x80
#define ENSELO 0x40
#define ENSELI 0x20
#define ENRESELI 0x10
#define ENAUTOATNO 0x08
#define ENAUTOATNI 0x04
#define ENAUTOATNP 0x02
#define SCSIRSTO 0x01
/* SCSI transfer control 0 */
#define SCSIEN 0x80
#define DMAEN 0x40
#define CH1 0x20
#define CLRSTCNT 0x10
#define SPIOEN 0x08
#define CLRCH1 0x02
/* SCSI transfer control 1 */
#define BITBUCKET 0x80
#define SWRAPEN 0x40
#define ENSPCHK 0x20
#define STIMESEL 0x18 /* mask */
#define STIMESEL_ 3
#define ENSTIMER 0x04
#define BYTEALIGN 0x02
/* SCSI signal IN */
#define CDI 0x80
#define IOI 0x40
#define MSGI 0x20
#define ATNI 0x10
#define SELI 0x08
#define BSYI 0x04
#define REQI 0x02
#define ACKI 0x01
/* SCSI Phases */
#define P_MASK (MSGI|CDI|IOI)
#define P_DATAO (0)
#define P_DATAI (IOI)
#define P_CMD (CDI)
#define P_STATUS (CDI|IOI)
#define P_MSGO (MSGI|CDI)
#define P_MSGI (MSGI|CDI|IOI)
/* SCSI signal OUT */
#define CDO 0x80
#define IOO 0x40
#define MSGO 0x20
#define ATNO 0x10
#define SELO 0x08
#define BSYO 0x04
#define REQO 0x02
#define ACKO 0x01
/* SCSI rate control */
#define SXFR 0x70 /* mask */
#define SXFR_ 4
#define SOFS 0x0f /* mask */
/* SCSI ID */
#define OID 0x70
#define OID_ 4
#define TID 0x07
/* SCSI transfer count */
#define GETSTCNT() ( (GETPORT(STCNT2) + (GETPORT(STCNT1) + GETPORT(STCNT0) )
#define SETSTCNT(X) { SETPORT(STCNT2, ((X) & 0xFF0000) >> 16); \
SETPORT(STCNT1, ((X) & 0x00FF00) >> 8); \
SETPORT(STCNT0, ((X) & 0x0000FF) ); }
/* SCSI interrupt status */
#define TARGET 0x80
#define SELDO 0x40
#define SELDI 0x20
#define SELINGO 0x10
#define SWRAP 0x08
#define SDONE 0x04
#define SPIORDY 0x02
#define DMADONE 0x01
#define SETSDONE 0x80
#define CLRSELDO 0x40
#define CLRSELDI 0x20
#define CLRSELINGO 0x10
#define CLRSWRAP 0x08
#define CLRSDONE 0x04
#define CLRSPIORDY 0x02
#define CLRDMADONE 0x01
/* SCSI status 1 */
#define SELTO 0x80
#define ATNTARG 0x40
#define SCSIRSTI 0x20
#define PHASEMIS 0x10
#define BUSFREE 0x08
#define SCSIPERR 0x04
#define PHASECHG 0x02
#define REQINIT 0x01
#define CLRSELTIMO 0x80
#define CLRATNO 0x40
#define CLRSCSIRSTI 0x20
#define CLRBUSFREE 0x08
#define CLRSCSIPERR 0x04
#define CLRPHASECHG 0x02
#define CLRREQINIT 0x01
/* SCSI status 2 */
#define SOFFSET 0x20
#define SEMPTY 0x10
#define SFULL 0x08
#define SFCNT 0x07 /* mask */
/* SCSI status 3 */
#define SCSICNT 0xf0 /* mask */
#define SCSICNT_ 4
#define OFFCNT 0x0f /* mask */
/* SCSI TEST control */
#define SCTESTU 0x08
#define SCTESTD 0x04
#define STCTEST 0x01
/* SCSI status 4 */
#define SYNCERR 0x04
#define FWERR 0x02
#define FRERR 0x01
#define CLRSYNCERR 0x04
#define CLRFWERR 0x02
#define CLRFRERR 0x01
/* SCSI interrupt mode 0 */
#define ENSELDO 0x40
#define ENSELDI 0x20
#define ENSELINGO 0x10
#define ENSWRAP 0x08
#define ENSDONE 0x04
#define ENSPIORDY 0x02
#define ENDMADONE 0x01
/* SCSI interrupt mode 1 */
#define ENSELTIMO 0x80
#define ENATNTARG 0x40
#define ENSCSIRST 0x20
#define ENPHASEMIS 0x10
#define ENBUSFREE 0x08
#define ENSCSIPERR 0x04
#define ENPHASECHG 0x02
#define ENREQINIT 0x01
/* DMA control 0 */
#define ENDMA 0x80
#define _8BIT 0x40
#define DMA 0x20
#define WRITE_READ 0x08
#define INTEN 0x04
#define RSTFIFO 0x02
#define SWINT 0x01
/* DMA control 1 */
#define PWRDWN 0x80
#define STK 0x07 /* mask */
/* DMA status */
#define ATDONE 0x80
#define WORDRDY 0x40
#define INTSTAT 0x20
#define DFIFOFULL 0x10
#define DFIFOEMP 0x08
/* BURST control */
#define BON 0xf0
#define BOFF 0x0f
/* TEST REGISTER */
#define BOFFTMR 0x40
#define BONTMR 0x20
#define STCNTH 0x10
#define STCNTM 0x08
#define STCNTL 0x04
#define SCSIBLK 0x02
#define DMABLK 0x01
/* On the AHA-152x board PORTA and PORTB contain
some information about the board's configuration. */
typedef union {
struct {
unsigned reserved:2; /* reserved */
unsigned tardisc:1; /* Target disconnect: 0=disabled, 1=enabled */
unsigned syncneg:1; /* Initial sync neg: 0=disabled, 1=enabled */
unsigned msgclasses:2; /* Message classes
0=#4
1=#0, #1, #2, #3, #4
2=#0, #3, #4
3=#0, #4
*/
unsigned boot:1; /* boot: 0=disabled, 1=enabled */
unsigned dma:1; /* Transfer mode: 0=PIO; 1=DMA */
unsigned id:3; /* SCSI-id */
unsigned irq:2; /* IRQ-Channel: 0,3=12, 1=10, 2=11 */
unsigned dmachan:2; /* DMA-Channel: 0=0, 1=5, 2=6, 3=7 */
unsigned parity:1; /* SCSI-parity: 1=enabled 0=disabled */
} fields;
unsigned short port;
} aha152x_config ;
#define cf_parity fields.parity
#define cf_dmachan fields.dmachan
#define cf_irq fields.irq
#define cf_id fields.id
#define cf_dma fields.dma
#define cf_boot fields.boot
#define cf_msgclasses fields.msgclasses
#define cf_syncneg fields.syncneg
#define cf_tardisc fields.tardisc
#define cf_port port
/* Some macros to manipulate ports and their bits */
#define SETPORT(PORT, VAL) \
outb( (VAL), (PORT) )
#define SETPORTP(PORT, VAL) \
outb_p( (VAL), (PORT) )
#define SETPORTW(PORT, VAL) \
outw( (VAL), (PORT) )
#define GETPORT(PORT) \
inb( PORT )
#define GETPORTW(PORT) \
inw( PORT )
#define SETBITS(PORT, BITS) \
outb( (inb(PORT) | (BITS)), (PORT) )
#define CLRBITS(PORT, BITS) \
outb( (inb(PORT) & ~(BITS)), (PORT) )
#define CLRSETBITS(PORT, CLR, SET) \
outb( (inb(PORT) & ~(CLR)) | (SET) , (PORT) )
#define TESTHI(PORT, BITS) \
((inb(PORT) & (BITS)) == BITS)
#define TESTLO(PORT, BITS) \
((inb(PORT) & (BITS)) == 0)
#endif /* _AHA152X_H */
