This document provides practical, common guidelines for incorporating PCI Express interconnect
layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10-
layer or more server baseboard designs. Guidelines and constraints in this document are intended
for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI
Express devices located on the same baseboard (chip-to-chip routing) and interconnects between
a PCI Express device located “down” on the baseboard and a device located “up” on an add-in
card attached through a connector.
This document is intended to cover all major components of the physical interconnect including
design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card
edge-finger and connector considerations. The intent of the guidelines and examples is to help
ensure that good high-speed signal design practices are used and that the timing/jitter and
loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect.
However, while general physical guidelines and suggestions are given, they may not necessarily
guarantee adequate performance of the interconnect for all layouts and implementations.
Therefore, designers should consider modeling and simulation of the interconnect in order to
ensure compliance to all applicable specifications.
The document is composed of two main sections. The first section provides an overview of
general topology and interconnect guidelines. The second section concentrates on physical layout
constraints where bulleted items at the beginning of a topic highlight important constraints, while
the narrative that follows offers additional insight.
资源简介：This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guideline...
上传时间： 2013-10-15
上传用户：busterman
资源简介：This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guideline...
上传时间： 2014-01-24
上传用户：s363994250
资源简介：pcb shej PCB 设计规范 下载看看
上传时间： 2013-04-24
上传用户：yyq123456789
资源简介：华为印刷电路板PCB设计规范 华为企业技术标准，有一定参考意义
上传时间： 2013-07-15
上传用户：royzhangsz
资源简介：开关电源的PCB设计规范 在任何开关电源设计中，PCB板的物理设计都是最后一个环节，如果设计方法不当，PCB可能会辐射过多的电磁干扰，造成电源工作不稳定，以下针对各个步骤中所需注意的事项进行分析
上传时间： 2013-04-24
上传用户：pkkkkp
资源简介：华硕内部的PCB设计规范,华硕内部的PCB设计规范
上传时间： 2013-06-15
上传用户：brucewan
资源简介：和记奥普泰通信技术有限公司 印刷电路板PCB设计规范
上传时间： 2013-04-24
上传用户：kksuyiwen
资源简介：PCB设计规范2010最新版，79页经典讲解，设计者不可不看！
上传时间： 2013-07-31
上传用户：franktu
资源简介：台湾神达电脑集团pcb设计规范
上传时间： 2013-06-28
上传用户：tyg88888
资源简介：开关电源的PCB设计规范与方法
上传时间： 2013-10-28
上传用户：MATAIYES
