All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-
Triggers are intended to always provide proper internal low and high levels, even if an
undefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.
The hysteresis of these inputs, however, is very small, and can not be properly used in an
application to suppress signal noise, and to shape slow rising/falling input transitions.
Thus, it must be taken care that rising/falling input signals pass the undefined area of the
TTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usual
and specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).
The effect of the implemented Schmitt-Trigger is that even if the input signal remains in
the undefined area, well defined low/high levels are generated internally. Note that all
input signals are evaluated at specific sample points (depending on the input and the
peripheral function connected to it), at that signal transitions are detected if two
consecutive samples show different levels. Thus, only the current level of an input signal
at these sample points is relevant, that means, the necessary rise/fall times of the input
signal is only dependant on the sample rate, that is the distance in time between two
consecutive evaluation time points. If an input signal, for instance, is sampled through
software every 10us, it is irrelevant, which input level would be seen between the
samples. Thus, it would be allowable for the signal to take 10us to pass through the
undefined area. Due to the sample rate of 10us, it is assured that only one sample can
occur while the signal is within the undefined area, and no incorrect transition will be
detected. For inputs which are connected to a peripheral function, e.g. capture inputs, the
sample rate is determined by the clock cycle of the peripheral unit. In the case of the
CAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requires
input signals to pass through the undefined area within these 400ns in order to avoid
multiple capture events.
资源简介：All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is external...
上传时间： 2014-04-02
上传用户：han_zh
资源简介：传感器与检测技术 PPT版
上传时间： 2013-06-02
上传用户：eeworm
资源简介：Luminary Micro在Stellaris系列微控制器的部分产品中提供了模数转换器（ADC）模块。ADC的硬件分辨率为10位，但由于噪音和其它使精度变小的因素的影响，实际的精度小于10位。本应用文档提供了一个基于软件的过采样技术，从而使转换结果的有效位数（ENOB）得到...
上传时间： 2014-05-07
上传用户：drink！
资源简介： 本资料是关于意法半导体的STM8L和STM32L系列微控制器的可用封装汇总。 图 STM8L系列微控制器的部分可用封装
上传时间： 2013-11-10
上传用户：丶灬夏天
资源简介：C51系列微控制器的开发工具 uVision2入门教程 使用指南
上传时间： 2013-12-02
上传用户：busterman
资源简介：AT91SAM 系列微控制器的NAND Flash支持代码 描述怎样将NAND Flash和AT91SAM 系列微控制器连接起来。
上传时间： 2015-08-07
上传用户：stella2015
资源简介：选择Stellaris（群星）系列微控制器的理由
上传时间： 2016-03-30
上传用户：思琦琦
资源简介：瑞佑RA880X系列微控制器的官方驱动程序及DEMO例程，稍加修改就可移植。花了点精力下载到的。
上传时间： 2013-12-28
上传用户：dave520l
资源简介：示波器前端设计参考方案：具有50Ω 输入、模拟前端、 2GHz 的输入信号带宽(原理图+PCB)
上传时间： 2022-07-27
上传用户：ttalli
资源简介：本套书分上、下册。上册以PHILIPS公司的LPC2131 ARM微控制器为核心，以EasyARM2131开发板为基础，深入浅出地对LPC213x系列ARM微控制器的使用进行了详细、全方位的阐述。全书共分5章。第1章介绍EasyARM2131硬件开发平台；第2章介绍嵌入式开发软件平台；第3章着...
上传时间： 2013-12-26
上传用户：zhouli
