# # wan devices configuration # mainmenu_option next_comment comment 'Wan interfaces' bool 'Wan interfaces support' CONFIG_WAN if [ "$CONFIG_WAN" = "y" ]; then # There is no way to detect a comtrol sv11 - force it modular for now. if [ "$CONFIG_ISA" = "y" ]; then dep_tristate ' Comtrol Hostess SV-11 support' CONFIG_HOSTESS_SV11 m # The COSA/SRP driver has not been tested as non-modular yet. dep_tristate ' COSA/SRP sync serial boards support' CONFIG_COSA m fi # # COMX drivers # tristate ' MultiGate (COMX) synchronous serial boards support' CONFIG_COMX if [ "$CONFIG_COMX" != "n" ]; then dep_tristate ' Support for COMX/CMX/HiCOMX boards' CONFIG_COMX_HW_COMX $CONFIG_COMX dep_tristate ' Support for LoCOMX board' CONFIG_COMX_HW_LOCOMX $CONFIG_COMX dep_tristate ' Support for MixCOM board' CONFIG_COMX_HW_MIXCOM $CONFIG_COMX dep_tristate ' Support for MUNICH based boards: SliceCOM, PCICOM (WelCOM)' CONFIG_COMX_HW_MUNICH $CONFIG_COMX dep_tristate ' Support for HDLC and syncPPP protocols on MultiGate boards' CONFIG_COMX_PROTO_PPP $CONFIG_COMX if [ "$CONFIG_LAPB" = "y" ]; then dep_tristate ' Support for LAPB protocol on MultiGate boards' CONFIG_COMX_PROTO_LAPB $CONFIG_COMX fi if [ "$CONFIG_LAPB" = "m" ]; then dep_tristate ' Support for LAPB protocol on MultiGate boards' CONFIG_COMX_PROTO_LAPB $CONFIG_LAPB fi dep_tristate ' Support for Frame Relay on MultiGate boards' CONFIG_COMX_PROTO_FR $CONFIG_COMX fi # # The Etinc driver has not been tested as non-modular yet. # dep_tristate ' Etinc PCISYNC serial board support (EXPERIMENTAL)' CONFIG_DSCC4 m # FarSite Communications' cards tristate ' FarSync T-Series X.21 (and V.35/V.24) cards' CONFIG_FARSYNC # # Lan Media's board. Currently 1000, 1200, 5200, 5245 # tristate ' LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards' CONFIG_LANMEDIA # # ATI's sync/async boards. Currently 2520, 4020, 4520, 8520 -- 0 in second digit means async only # tristate ' Aurora Technology, Inc. synchronous asynchronous PCI cards V2' CONFIG_ATI_XX20 # There is no way to detect a Sealevel board. Force it modular dep_tristate ' Sealevel Systems 4021 support' CONFIG_SEALEVEL_4021 m tristate ' SyncLink HDLC/SYNCPPP support' CONFIG_SYNCLINK_SYNCPPP tristate ' Generic HDLC driver' CONFIG_HDLC if [ "$CONFIG_HDLC" != "n" ]; then bool ' Synchronous Point-to-Point Protocol (PPP) support' CONFIG_HDLC_PPP if [ "$CONFIG_LAPB" = "m" -a "$CONFIG_HDLC" = "m" -o "$CONFIG_LAPB" = "y" ]; then bool ' X.25 protocol support' CONFIG_HDLC_X25 else comment ' X.25/LAPB support is disabled' fi dep_tristate ' SDL RISCom/N2 support' CONFIG_N2 $CONFIG_HDLC dep_tristate ' Moxa C101 support' CONFIG_C101 $CONFIG_HDLC fi tristate ' Frame relay DLCI support' CONFIG_DLCI if [ "$CONFIG_DLCI" != "n" ]; then int ' Max open DLCI' CONFIG_DLCI_COUNT 24 int ' Max DLCI per device' CONFIG_DLCI_MAX 8 dep_tristate ' SDLA (Sangoma S502/S508) support' CONFIG_SDLA $CONFIG_DLCI fi # Wan router core. if [ "$CONFIG_WAN_ROUTER" != "n" ]; then bool ' WAN router drivers' CONFIG_WAN_ROUTER_DRIVERS if [ "$CONFIG_WAN_ROUTER_DRIVERS" = "y" ]; then dep_tristate ' Sangoma WANPIPE(tm) multiprotocol cards' CONFIG_VENDOR_SANGOMA $CONFIG_WAN_ROUTER if [ "$CONFIG_VENDOR_SANGOMA" != "n" ]; then bool ' WANPIPE Cisco HDLC support' CONFIG_WANPIPE_CHDLC bool ' WANPIPE Frame Relay support' CONFIG_WANPIPE_FR bool ' WANPIPE X.25 support' CONFIG_WANPIPE_X25 bool ' WANPIPE PPP support' CONFIG_WANPIPE_PPP bool ' WANPIPE Multi-Port PPP support' CONFIG_WANPIPE_MULTPPP fi if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then dep_tristate ' Cyclom 2X(tm) cards (EXPERIMENTAL)' CONFIG_CYCLADES_SYNC $CONFIG_WAN_ROUTER_DRIVERS $CONFIG_ISA if [ "$CONFIG_CYCLADES_SYNC" != "n" ]; then bool ' Cyclom 2X X.25 support (EXPERIMENTAL)' CONFIG_CYCLOMX_X25 fi fi fi fi # X.25 network drivers if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then dep_tristate ' LAPB over Ethernet driver (EXPERIMENTAL)' CONFIG_LAPBETHER $CONFIG_LAPB $CONFIG_X25 dep_tristate ' X.25 async driver (EXPERIMENTAL)' CONFIG_X25_ASY $CONFIG_LAPB $CONFIG_X25 fi if [ "$CONFIG_X86" = "y" ]; then tristate ' Granch SBNI12 Leased Line adapter support' CONFIG_SBNI if [ "$CONFIG_SBNI" != "n" ]; then bool ' Multiple line feature support' CONFIG_SBNI_MULTILINE fi fi fi endmenu
